MTX Audio Speaker 510CM User Manual

21A2692  
FIRST  
CLASS  
STAMP  
HERE  
MODEL 510CM  
WATER RESISTANT  
IN CEILING LOUDSPEAKER  
4545 E BASELINE RD  
PHOENIX AZ 85040-6400  
OWNERS MANUAL  
 
OTHER BLUEPRINT SERIES PRODUCTS FROM MTX  
MTX offers a wide assortment of audio components. Ranging from in-wall speakers to  
amplifiers to accessories. Each component is value engineered and must meet strict  
quality control standards before it becomes part of the MTX product line.  
LOUDSPEAKER PLACEMENT  
Blueprint Series Loudspeakers are designed to work within any interior decorat-  
ing scheme. They can be installed in virtually any location where flush mount-  
ing is possible. To maximize their sound performance however certain guidelines  
should be followed. For the best stereo reproduction the two loudspeakers should  
be placed an equal distance from your listening position and separated so that the  
angle between them, at the listening position, is between 40 and 60 degrees.  
Listed below you will find a sampling of MTX components available from your autho-  
rized Blueprint Series dealer.  
IN-WALL LOUDSPEAKERS  
MODEL 520W  
MODEL 502W  
5-1/4” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/84dB Sensitivity  
53Hz-20kHz Frequency Response  
50 Watts RMS/160 Watts Total  
11”H x 7-1/2”W x 2-1/2”D  
5-1/4” Two-Way In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/84dB Sensitivity  
53Hz-20kHz Frequency Response  
45 Watts RMS/140 Watts Total  
11”H x 7-1/2”W x 2-1/2”D  
MODEL 620W  
MODEL 602W  
6-1/2” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/85dB Sensitivity  
43Hz-20kHz Frequency Response  
55 Watts RMS/180 Watts Total  
12-1/16”H x 8-9/16”W x 2-7/8”D  
6-1/2” Two-Way In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/85dB Sensitivity  
43Hz-20kHz Frequency Response  
50 Watts RMS/160 Watts Total  
12-1/16”H x 8-9/16”W x 2-7/8”D  
MODEL 820W  
MODEL 600WM  
8” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/86dB Sensitivity  
33Hz-20kHz Frequency Response  
60 Watts RMS/200 Watts Total  
14-1/16”H x 10-1/16”W x 3-1/2”D  
6-1/2” Water Resistant Co-Axial In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/88dB Sensitivity  
64Hz-20kHz Frequency Response  
35 Watts RMS/140 Watts Total  
8-5/8”H x 8-5/8”W x 2-3/4”D  
SPEAKER/AMPLIFIER SELECTOR  
LPS-600  
Accommodates up to 6 pair of speakers  
Handles up to 250 Watts/channel continuous (RMS)  
Impedance Protection Circuitry  
Low profile-full size component  
Two-piece, plug in connectors on the rear panel  
Accommodates up to 14 gauge wire  
TV-5 UL Approved Switches  
A/B Amplifier and Input Selector  
ACCESSORIES  
VC-30B/VC-30W  
Decora-Style Volume Control (Bone or White)  
10 Step 25 Watts per channel (RMS) 150 Watts Peak  
AB-1SB/AB-1SW  
Decora-Style A/B Switch (Bone or White)  
PCK65C  
Pre-Construction Kit for Model 610RCM  
PCK85C  
Pre-Construction Kit for Model 810RCM  
 
STEP 1  
STEP 4  
Using a stud finder (available at low cost at most hardware stores) or other accu-  
rate method, locate center point between two joists and mark. Using template  
provided, trace hole pattern on surface of ceiling.  
Attach loudspeaker wires to speaker terminals, observing correct polarity, and  
position speaker frame up into cutout. Be careful not to pinch wires in the  
process.  
STEP 2  
STEP 5  
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol-  
lowing traced pattern.  
Carefully tighten the four mounting screws. This will cause the mounting wings  
to rotate out behind the mounting surface and secure the speaker in place.  
STEP 3  
STEP 6  
Run loudspeaker wires to sound source location. There are several methods you  
can use to accomplish wiring, depending on the construction characteristics of  
the room or house. You can add a professional touch to your installation by using  
a speaker terminal plate at the source location. Leave sufficient amount of wire  
at speaker location (8 to 10 inches) to complete connection.  
After the speaker panel is secured tightly, test for sound. When you are satisfied  
the speaker is operational, affix grill. The Model 510CM grill can be installed  
into the speaker frame for either a standard flush mount cosmetic appearance or  
a recessed look similar to a coilex type of light fixture. After deciding which look  
is preferred press the grill into the frame until the leading edge is flush.  
 

MTX Audio Speaker 620WE User Manual
Nokia Cell Phone Accessories Nokia 6210 User Manual
Nokia Cell Phone N92 User Manual
Oki Printer PAGE 24 User Manual
Olympus Camcorder SP 560UZ User Manual
Omega Thermostat DP25B TC User Manual
Oregon Scientific Radar Detector BAR933HG User Manual
Orion Car Audio Car Speaker P52 User Manual
Panasonic DVD Recorder DMR EH67 User Manual
Panasonic Ventilation Hood FV 08VKML2 User Manual