MTX Audio Speaker System HTB1 S User Manual

HTB1-S  
Home Theater Loudspeaker  
System  
1 Mitek Plaza  
Winslow, IL 61089  
815-367-3000  
800-225-5689  
21A8361  
 
SPECIFICATIONS  
HTB1 Satellite/Center Channel  
Driver Complement  
CENTER  
FRONT  
RIGHT  
FRONT  
LEFT  
FRONT  
Midrange- 3” shielded with paper cone, foam surround  
Tweeter- 1/2" Balanced dome tweeter  
Frequency Response: 150Hz - 20kHz  
Impedance: 8 ohms nominal  
HTB1  
SUBWOOFER  
45  
Power Handling: 75 watts RMS / 150 watts peak music  
Recommended Amplifier Power: 20-100 watts RMS  
Sensitivity: [email protected]/1M  
LEFT  
REAR  
RIGHT  
REAR  
LISTENING AREA  
Weight:  
Satellite- 1.8 lbs.  
Center Channel- 3.0 lbs  
Dimensions:  
Satellite- 6"H X 4 1/8"W X 4 1/8"D  
Center Channel- 4 1/8"H X 9 11/16"W X 3 7/8"D  
Figure 1- Typical loudspeaker placement in a home theater system.  
HTB1 Subwoofer  
Driver Complement  
Woofer- 8" high excursion woofer  
Amplifier Power: 120W Peak Music Power  
Crossover Frequency: continuously variable 50Hz-150Hz  
Frequency Response: 50Hz - 150Hz  
Enclosure: tuned port design  
Weight: 16.5 lbs.  
Dimensions: 13 3/4” H X 10” W X 13 3/16” D  
Figure 2- Proper placement of left/center/right front speakers.  
Optional Installation Accessories  
A. Feet for Satellites  
Included in the system are rubber feet that allow you to raise the Satellite  
Speakers up off of a level surface. Simply peel each of the four feet off the  
sheet and press on to the bottom of the Satellite Speaker. Repeat steps for  
the remaining Satellite Speakers.  
B. Feet for Center Channel  
Included in the system are plastic feet that allow the Center Channel to be  
angled more horizontally on top of your television monitor. If you wish to use  
the feet, simply insert the knurled end of the feet into the two holes in the lower  
rear of the Center Channel.  
Figure 3- Improper placement of left/center/right front speakers  
 
EXPLANATION OF FEATURES AND CONTROLS  
WIRING AND CONNECTIONS  
Turn off all power to your subwoofer and other equipment before making  
any connections.  
Refer to Figure A  
Installation using speaker level inputs (Figure B).  
1) Power Switch: This two position switch controls the power status of the sub-  
woofer.  
Off: Turns the unit off.  
A/V Receiver or Amplifier  
+ -  
+ -  
LEFT  
FRONT  
RIGHT  
FRONT  
On: Turns the unit on regardless of whether a signal is present or not.  
2) Subwoofer crossover (Freq): This rotary control adjusts a variable low pass fil-  
ter to set the upper frequency at which the output of the subwoofer begins to roll-  
off. Continuously variable from 50Hz to 150 Hz, it matches the upper frequency  
characteristics of the subwoofer to the low frequency response of the main stereo  
speakers. Recommended setting: 120Hz-150Hz.  
FRONT  
CENTER  
SURROUND  
FREQ  
GAIN  
FROM AMPLIFIER  
L
R
POWER  
50Hz 150Hz  
L
R
MIN MAX  
LINE IN  
HI LEVEL IN  
3) Line level input: These RCA phono jacks accept a line level full range signal  
from the preamplifier output of a receiver or preamplifier. This full range signal is  
processed and amplified to power the subwoofer.  
FUSE 1A/250V  
+
-
ON  
1A 250V  
4) Speaker level (high level) input: These spring loaded terminals for speaker wire  
accept a stereo, speaker level, full range signal from a receiver or power amplifier.  
This signal is processed and amplified to power the subwoofer.  
5) Fuse: For continued protection replace fuse with same type and size listed.  
6) Level control (Gain): This rotary control adjusts the level of the subwoofer and  
is used to balance its volume with that of the main stereo speakers.  
7) Status LED: This light emitting diode shows the status of the subwoofer elec-  
tronics. "Red" indicates that the amplifier is plugged in and the power switch is  
on.  
CENTER  
FRONT  
OFF  
120 VAC  
100 WATTS  
60 HZ  
Made In China  
-
+
-
+
LEFT  
REAR  
RIGHT  
REAR  
FIGURE B  
Installation with A/V amplifiers and receivers that have 5.1 channel line level  
output (Figure C).  
Use an RCA "Y" adaptor to connect both line level inputs.  
3
4
6
2
7
OUTPUTS  
A/V Receiver or Amplifier  
FREQ  
GAIN  
FROM AMPLIFIER  
SUB  
L
FREQ  
GAIN  
FROM AMPLIFIER  
L
R
POWER  
50Hz 150Hz  
L
R
FRONT  
CENTER  
SURROUND  
MIN MAX  
R
POWER  
50Hz 150Hz  
LINE IN  
HI LEVEL IN  
L
R
MIN MAX  
LINE IN  
HI LEVEL IN  
FUSE 1A/250V  
FUSE 1A/250V  
ON  
1A 250V  
+ -  
+ -  
5
+
-
ON  
1A 250V  
OFF  
1
CENTER  
FRONT  
120 VAC  
100 WATTS  
60 HZ  
RIGHT  
FRONT  
LEFT  
FRONT  
OFF  
120 VAC  
100 WATTS  
60 HZ  
Made In China  
-
+
-
+
Made In China  
RIGHT  
REAR  
LEFT  
REAR  
FIGURE C  
FIGURE A  
 

Miele Clothes Dryer T 4162 User Manual
Mr Coffee Coffeemaker SKX20 099 User Manual
MTX Audio Car Speaker AW52 User Manual
National Instruments Network Card NI PCIe 8231 User Manual
Niles Audio Universal Remote ZR PRO User Manual
Nintendo Video Games 658A61A User Manual
Nokia Bluetooth Headset 6300 User Manual
NordicTrack Treadmill NCTL09990 User Manual
Numark Industries Turntable DM905 User Manual
Palsonic CRT Television 5159P User Manual