150
100
®
OMEGA
50
200
0
250
MODEL J DIALTEMP™
INSTRUCTION
SHEET
M0102/0902
INTRODUCTION
TM
The Model J Dialtemp is a non electronic thermometer that features a 360
degree swivel neck with a 90 degree tilt range of it’s large easy-to-read 5
inch dial face. The heliarc stainless steel welded construction provides a
moisture-proof bond, while preventing the possibility of rust and corrosion.
The temperature sensing device consists of sensitive bi-metal coils. They are
wound to pre-determined standards and are individually trimmed and
tested for full-scale accuracy, contributing minimum pointer vibration and
maximum heat transfer. One external reset screw enables fast and simple
recalibration. This superior DialTemp instrumentation design combines
high precision with durability and dependability, making the Model J
Thermometer ideal for a wide variety of applications.
UNPACKING INSTRUCTIONS
Remove the packing list and verify that all equipment has been received. If
there are any questions about the shipment, please call the OMEGA
Customer Service Department at 1-800-622-2378 or (203) 359-1660.
Upon receipt of shipment, inspect the container and equipment for signs of
damage. Take particular note of any evidence of rough handling in transit.
Immediately report any damage to the shipping agent.
NOTE
The carrier will not honor any claims unless all shipping
material is saved for their examination. After examining and
removing contents, save packing material in event reshipment
is necessary.
HEAD ADJUSTMENT INSTRUCTIONS
Adjust the angle of the head before installing the Model J Thermometer.
Refer to Figure 1 to locate the adjustment screws.
NOTE
Install the thermometer so that the maximum ambient head
temperature remains below 300°F (149°C) at all times.
1. Adjust the rotational position of the head by loosening the two bracket
bolts and rotating the bracket until the head is in the desired position.
1
RECALIBRATION:
External ⁄4" nut reset screw
OVERRANGE PROTECTION: 50% up to 500°F
MATERIALS:
CONSTRUCTION:
Stainless steel welded construction (rust and
corrosion-proof, leakproof, hermetically sealed)
PRESSURE RATING: Rated to 1,000 PSI. Use of thermowell is
recommended for higher pressures or for
very heavy-duty applications.
HEAD & BEZEL:
MOUNTING:
DIAL FACE:
Polished Type 302 stainless steel
1
5
⁄
2"-14 NPT, Type 303 stainless steel, ⁄8" wrench flats.
Anodized aluminum. Black marks and numbers
with stain matte finish background. Easy to read.
Minimum parallax.
STEM:
Type 304 stainless steel (highly resistant to
corrosion)
CRYSTAL:
OPTIONAL:
Optically clear strong glass.
Unbreakable clear plastic (not recommended for
ranges over 300°F)
DIMENSIONS:
HEAD DIAMETER:
STEM DIAMETER:
STEM LENGTH:
5" dia.
1
⁄4" dia.
1
standard is 2 ⁄ " or 6". Also available: 4", 9", 12",
2
15", 18", 24", 30", 36". NOTE: A 4" stem is the
shortest length for ranges 0-100°F, 25-125°F, and
0-50°C.
Optional on all models -excellent for probing
asphalt, compost, soil, frozen foods, and other
POINTED STEMS:
semi-solid materials.
1
RESET SCREW:
OPTIONAL FEATURES:
⁄
4" hex nut with slot for screwdriver.
", ⁄4" NPT Adaptor Bushing (other threads
1
3
⁄
2
available on special order)
HEAD SIZE 76.2 OR 127
(3 OR 5)
77.0
(3.03)
C STEM
L
ROTATE
19.1 (.75)
5.1 (.20)
TILT
.72
(18.3)
RESET
SCREW
39.6 (1.56)
36.3 (1.43)
12.7 (.50)
15.7 (.62)
(WRENCH FLATS)
15.7 (.62)
1/2-14 NPT
6.4 (.25)
STEM LENGTH
Figure 1. Dimensions Model J
Servicing Europe:
Benelux:
Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: +31 (0)20 3472121
FAX: +31 (0)20 6434643
OMEGAnet® Online Service
Internet e-mail
Toll Free in Benelux: 0800 0993344
e-mail: [email protected]
Czech
Rudé armády 1868, 733 01 Karviná 8
Servicing North America:
Republic:
Tel: +420 (0)69 6311899
Toll Free: 0800-1-66342
FAX: +420 (0)69 6311114
e-mail: [email protected]
USA:
ISO 9001 Certified
One Omega Drive, Box 4047
Stamford CT 06907-0047
Tel: (203) 359-1660
France:
11, rue Jacques Cartier, 78280 Guyancourt, France
Tel: +33 (0)1 61 37 29 00 FAX: +33 (0)1 30 57 54 27
Toll Free in France: 0800 466 342
e-mail: [email protected]
FAX: (203) 359-7700
e-mail: [email protected]
Canada:
976 Bergar
Laval (Quebec) H7L 5A1
Tel: (514) 856-6928
e-mail: [email protected]
Germany/
Austria:
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
FAX: (514) 856-6886
Tel: +49 (0)7056 9398-0
FAX: +49 (0)7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: [email protected]
For immediate technical or application assistance:
®
United
One Omega Drive, River Bend Technology Centre
Northbank, Irlam, Manchester
USA and
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
Customer Service: 1-800-622-2378 / 1-800-622-BEST
®
Kingdom:
Canada:
®
ISO 9002 Certified M44 5BD United Kingdom
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Tel: +44 (0)161 777 6611
FAX: +44 (0)161 777 6622
Toll Free in United Kingdom: 0800-488-488
e-mail: [email protected]
Mexico:
En Espan˜ol: (001) 203-359-7803
FAX: (001) 203-359-7807
e-mail:[email protected]
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its
products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter
specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient-connected applications.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from
date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each
product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the
purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or
unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of OMEGA’s control. Components which wear are not warranted,
including but not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with
information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as
specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this
order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential,
incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR
21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s)
be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes
no responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and
hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following informa-
tion available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
FOR NON-WARRANTY REPAIRS, consult OMEGA for cur-
rent repair charges. Have the following information avail-
able BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the
product.
3. Repair instructions and/or specific problems relative to
the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in
technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING,
INC.
M0102/0902
|