KDC-W4531
KDC-W4031
KDC-W431G
KDC-W409
KDC-3031A
KDC-3031G
KDC-309A
KDC-309G
CD-RECEIVER
INSTRUCTION MANUAL
© B64-2932-00/00 (EW/EN/E2W/E2N)
Safety precautions
About CD players/disc changers
connected to this unit
KENWOOD disc changers/ CD players released in
1998 or later can be connected to this unit.
Refer to the catalog or consult your Kenwood
dealer for connectable models of disc changers/
CD players.
2WARNING
To prevent injury or fire, take the
following precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools)
inside the unit.
Note that any KENWOOD disc changers/ CD players
released in 1997 or earlier and disc changers made
by other makers cannot be connected to this unit.
Unsupported connection may result in damage.
Setting the "O-N" Switch to the "N" position for the
applicable KENWOOD disc changers/ CD players.
The functions that can be used and the information
that can be displayed will differ depending on the
models being connected.
2CAUTION
To prevent damage to the machine, take
the following precautions:
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not set the removed faceplate or the faceplate
case in areas exposed to direct sunlight, excessive
heat or humidity. Also avoid places with too much
dust or the possibility of water splashing.
•
You can damage both your unit and the CD changer if
you connect them incorrectly.
Lens Fogging
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called lens
fogging, CDs may be impossible to play. In such
a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does
not operate normally after a while, consult your
Kenwood dealer.
• To prevent deterioration, do not touch the
terminals of the unit or faceplate with your
fingers.
• Do not subject the faceplate to excessive shock,
as it is a piece of precision equipment.
• When replacing a fuse, only use a new one with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
Do Not Load 8 cm (3 in.) CDs in the CD
slot
If you try to load a 8 cm (3 in.) CD with its adapter
into the unit, the adapter might separate from the
CD and damage the unit.
|
English
3
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when
the Reset button is pressed.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 23).
• Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be
restored.
About DAB Tuner control
(KDC-W4531)
Refer to A group on the Instruction manual of DAB
Tuner KTC-9090DAB (optional accessory) for the
control method of DAB Tuner function.
SCRL
However, the following control methods of the
function for this unit may be differed from the
Instruction manual; therefore, refer to the following
supplemental instruction.
+
VOL
AUD
PTY
DISP
SET UP
Q
MENU
OFF
SCAN
RDM
REP
-
TI
AME
<Auto Ensemble Memory Entry>
1. Select the preset band for Auto Ensemble
Memory Entry.
Reset button
2. Press the [AME] button for at least 2 seconds.
Open Auto Ensemble Memory Entry.
After storing in the memory finishes, the
number of the pre-set buttons and the
ensemble label are displayed.
<Searching by programme type and language>
and <Languages to be displayed>
At the operation to press [DISP] button, press [TI]
button.
<Automatic Switching DAB priority>
• The characters which can be displayed by this
unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;
^ - { } | ~ .
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on
the display on the actual equipment, and some
of the illustrations on the display may represent
something impossible in actual operation.
This function cannot be used.
This Product is not installed by the manufacturer
of a vehicle on the production line, nor by the
professional importer of a vehicle into an EU
Member State.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off
with a cloth moistened with neutral cleaner, then
wipe neutral detergent off.
The marking of products using lasers
(Except for some areas)
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth
or using a volatile liquid such as thinner or alcohol may
scratch the surface or erases characters.
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have
been classified as Class 1. It means that the unit
is utilizing laser beams that are of a weaker class.
There is no danger of hazardous radiation outside
the unit.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty,
wipe them with a dry, soft cloth.
|
4
English
About CDs
Handling CDs
• Don’t touch the recording surface of the CD.
Removing CDs
When removing CDs from this unit pull them out
horizontally.
CDs that can’t be used
• CDs that aren’t round can’t be used.
• CD-R and CD-RW are easier to damage than a
normal music CD. Use a CD-R or a CD-RW after
reading the caution items on the package etc.
• Don’t stick tape etc. on the CD.
Also, don’t use a CD with tape stuck on it.
• CDs with coloring on the recording surface or that
are dirty can’t be used.
• This unit can only play the CDs with
When using a new CD
If the CD center hole or outside rim has burrs, use it
after removing them with a ball pen etc.
.
It may not correctly play discs which do not have
the mark.
• A CD-R or CD-RW that hasn’t been finalized can’t
be played. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-
R/CD-RW recorder instruction manual.)
Burrs
Burrs
CD storage
• Don’t place them in direct sunlight (On the seat
or dashboard etc.) and where the temperature is
high.
• Store CDs in their cases.
CD accessories
Don’t use disc type accessories.
CD cleaning
Clean from the center of the disc and move
outward.
|
English
5
About MP3 and WMA
The playable MP3/WMA file (hereafter called
Audio file) and the media format has the following
limitation. The Audio file, which is out of the
specification, may not able to be played normally,
or the file and folder names may not be displayed
correctly.
The maximum number of characters for
this unit
File/Folder name: 64 (Joliet: 32) characters
ID3 Tag/Contents property (WMA): 30 characters
•
•
File/Folder name is the number of the characters
including the extensions
ID3 Tag can only display the tag of Ver1.X.
Playable Audio file
•
MP3, WMA: KDC-W4531/W4031/W409/W431G
Limitation of structure for the file and the
folder
•
•
Attach the correct extension for the Audio file
(MP3: ".MP3", WMA: ".WMA")
Do not attach the extensions to the other files besides
the Audio file. If it is attached, the file, which is not the
Audio file, will be played and outputs the loud noise, and
then the speaker will be damaged.
• Maximum number of directory levels: 8
• Maximum number of folders: 50
• Maximum number of files per folder: 255
• Maximum number of files and folders: 512
•
The files with copy protection cannot be played.
Playing order of the Audio file
The Audio file is played in the order which is written
by writing soft. You may be able to set the playing
order by writing the play sequence numbers such
as "01" to "99" at the beginning of the file name.
Playable MP3 file
• MPEG 1/2 Audio Layer 3 file
• Transfer bit rate: 8-320 kbps
• Sampling frequency
Example
: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz
0
¡
: Folder
: Audio file
CD
(1)
Playable WMA file
• The file in accordance with Windows Media Audio
(Except for the file for Windows Media Player 9 or
after which applies the new functions)
¡!
2
¡"
3
• Transfer bit rate: 48-192 kbps
• Sampling frequency: 32, 44.1, 48 kHz
¡#
¡$
Playable media
• CD-ROM, CD-R, CD-RW (CD-RW with quick format
cannot be used.)
4
¡%
• Playing order after ¡! play
•
When recording to the media up to the maximum
¡"➡¡#➡¡$➡¡%...
capacity at once, the writing soft is set to "Disc at once".
• Forward file search during ¡# play (Push the
Control knob to [¢])
¡$
Playable disc format
• ISO 9660 Level 1/2
• Joliet
• Forward folder search during ¡" play (Push the
Control knob to [FM])
• Romeo
• Long file name.
: 3➡4...
• When it is set to directory 4, skip to the folder
before the same level by folder select (Push the
Control knob to [4])
: 2
• When it is set to directory 3, makes the level up
by folder select (Push the Control knob to [AM])
: 2
|
6
English
General features
VOL
Release button
Control knob
SCRL
+
VOL
AUD
SET UP
PTY
DISP
Q
MENU
OFF
SCAN
RDM
REP
ATT
-
DIM
TI
AME
ATT/DIM
Q
SRC
LOUD indicator
Clock display
ATT indicator
The time until full power OFF can be set in <Power
OFF Timer> (page 23).
Power
Turning ON the Power
Press the [SRC] button.
Turning OFF the Power
Press the [SRC] button for at least 1 second.
Volume
Increasing Volume
Turn the [VOL] knob clockwise.
Decreasing Volume
Turn the [VOL] knob counterclockwise.
Selecting the Source
Press the [SRC] button.
Source required
Tuner
CD
Display
"TUNER"
"CD"
Attenuator
Turning the volume down quickly.
External disc (Optional accessory)
Auxiliary input (Optional accessory)
Standby (Illumination only mode)
"CD CH"
"AUX EXT"
"STANDBY"
Press the [ATT] button.
Each time the button is pressed, the Attenuator
turns ON and OFF.
When it’s ON, the "ATT" indicator blinks.
•
This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicles battery.
|
English
7
General features
System Q
5 Exit Audio Control mode
Press any button.
Press the button which is not [VOL] knob and
[ATT] button.
You can recall the best sound setting preset for
different types of music.
1 Select the source to set
Press the [SRC] button.
2 Select the Sound type
Press the [Q] button.
Each time the button is pressed, the sound
setting switches.
Audio Setup
Setting the Sound system, such as Volume offset
and Loudness.
Sound setting
Natural
Rock
Pops
Easy
Display
"NATURAL"
"ROCK"
"POPS"
1 Select the source for adjustment
Press the [SRC] button.
2 Enter Audio Setup mode
Press the [VOL] knob for at least 1 second.
"EASY"
Top 40
Jazz
"TOP40"
"JAZZ"
3 Select the Audio Setup item for adjustment
Press the [VOL] knob.
Each time the knob is pressed, the items that can
be adjusted switch as shown below.
•
When the System Q setting is changed, the Bass,
Middle, and Treble set in audio control replace the
System Q values.
4 Adjust the Audio setup item
Turn the [VOL] knob.
•
•
"USER" : The values set on the <Audio Control> (page
8).
Each setting value is changed with the <Speaker
Setting> (page 8).
Adjustment Item Display
Range
–8 —
ON/OFF
Volume offset
Loudness
"V-OFF"
"LOUD"
0
First, select the speaker type with the Speaker setting.
•
•
Volume offset: Each source’s volume can be set as a
difference from the basic volume.
Loudness: Compensating for low and high tones
during low volume.
Audio Control
1 Select the source for adjustment
Press the [SRC] button.
When it's ON, "LOUD" indicator is ON.
5 Exit Audio Setup mode
Press the [VOL] knob for at least 1 second.
2 Enter Audio Control mode
Press the [VOL] knob.
3 Select the Audio item for adjustment
Press the [VOL] knob.
Each time the knob is pressed, the items that can
be adjusted switch as shown below.
Speaker Setting
Fine-tuning so that the System Q value is optimal
when setting the speaker type.
4 Adjust the Audio item
Turn the [VOL] knob.
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
Adjustment Item Display
Range
Bass level
Middle level
Treble level
Balance
"BAS L"
"MID L"
"TRE L"
"BAL"
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
2 Enter Speaker Setting mode
Press the [VOL] knob.
Fader
"FAD"
|
8
English
In CD & External disc source (KDC-W4531/
W4031/W409/W431G)
3 Select the Speaker type
Turn the [VOL] knob.
Each time the knob is turned, the setting
switches as shown below.
Information
Disc title
Track title
Track number & Play time
Clock
Display
"D-TITLE"
"T-TITLE"
"P-TIME"
"CLOCK"
Speaker type
OFF
For 5 & 4 in. speaker
For 6x9 &6 in. speaker
For the OEM speaker
Display
"SP OFF"
"SP 5/4"
"SP 6x9/6"
"SP OEM"
• External disc source: KDC-W4531
In Audio file source (KDC-W4531/W4031/
W409/W431G)
4 Exit Speaker Setting mode
Press the [VOL] knob.
Information
Display
Song title & Artist name
"TITLE"
Album name (MP3 only) & Artist name "ALBUM"
Folder name
File name
"FOLDER"
"FILE"
Switching Display
Track number & Play time
Clock
"P-TIME"
"CLOCK"
Switching the information displayed.
1 Enter Switching Display mode
Press the Control knob for at least 1 second.
"DISP SEL" is displayed.
In Auxiliary input source
Information
Auxiliary input name
Clock
Display
"SRC NAME"
"CLOCK"
2 Select the Display item
Push the Control knob to[4] or [¢].
In Tuner source (KDC-W431G)
3 Exit Switching Display mode
Information
Frequency
Clock
Display
"FREQ"
"CLOCK"
Press the Control knob.
•
If the Disc title, Track title, Song title & Artist name, or
Album name & Artist name is selected when the disc
which does not have Disc title, Track title, Song title,
Album name, or Artist name is played, track number
and play time are displayed.
In Tuner source
Information
Display
"FREQ"(MW/LW),
"FREQ/PS"(FM)
Program Service name or Frequency
Radio text, Program Service name or "R-TEXT"(FM)
Frequency
Clock
"CLOCK"
Dimmer Control
You can change the unit's display to dimmer.
The frequency is displayed during Program
Service name reception
Press the Control knob for at least 1 second.
The frequency for the RDS station will be
displayed for 5 seconds instead of the Program
Service name.
Press the [DIM] button for at least 1 second.
Each time the button is pressed for 1 second, the
Dimmer contol turns ON and OFF.
In CD source (KDC-3031A/3031G/309A/309G)
Information
Track number & Play time
Clock
Display
"P-TIME"
"CLOCK"
|
English
9
General features
Theft Deterrent Faceplate
TEL Mute
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
The audio system automatically mutes when a
call comes in.
Removing the Faceplate
Press the Release button.
The faceplate is unlocked, allowing you to detach
it.
When a call comes in
"CALL" is displayed.
The audio system pauses.
Listening to the audio during a call
Press the [SRC] button.
The "CALL" display disappears and the audio
system comes back ON.
•
•
The faceplate is a precision piece of equipment and
can be damaged by shocks or jolts. For that reason,
keep the faceplate in its special storage case while
detached.
Do not expose the faceplate or its storage case to
direct sunlight or excessive heat or humidity. Also
avoid places with too much dust or the possibility of
water splashing.
When the call ends
Hang up the phone.
The "CALL" display disappears and the audio
system comes back ON.
Reattaching the Faceplate
1 Align the projections on the unit with the
grooves on the faceplate.
Projections
Grooves
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to
use the unit.
|
10
English
Tuner features
SCRL
+
VOL
AUD
SET UP
PTY
DISP
Q
MENU
OFF
SCAN
RDM
REP
ATT
-
DIM
AUTO
AME
AUTO/ Control
knob
SRC
1 - 6
AME
ST indicator
Band display
Frequency display Preset station number
Function of the KDC-W431G
Tuning
Tuning Mode
Selecting the station.
Choose the tuning mode.
1 Select tuner source
Press the [AUTO] button.
Each time the button is pressed, the Tuning
mode switches as shown below.
Press the [SRC] button.
Select the "TUNER" display.
2 Select the band
Tuning mode
Display
Operation
Automatic search for a station.
Search in order of the stations
in the Preset memory.
Push the Control knob to [FM] or [AM].
Each time the knob is pushed to [FM], it switches
between the FM1, FM2, and FM3 bands.
Auto seek
"AUTO 1"
Preset station seek "AUTO 2"
Manual
"MANUAL" Normal manual tuning control.
3 Tune up or down band
Push the Control knob to [4] or [¢].
•
During reception of stereo stations the "ST" indicator
is ON.
|
English
11
Tuner features
Station Preset Memory
Putting the station in the memory.
1 Select the band
Push the Control knob to [FM] or [AM].
2 Select the frequency to put in the memory
Push the Control knob to [4] or [¢].
3 Put the frequency in the memory
Press the desired [1] — [6] button for at least
2 seconds.
The preset number display blinks 1 time.
On each band, 1 station can be put in the
memory on each [1] — [6] button.
Auto Memory Entry
Putting stations with good reception in the
memory automatically.
1 Select the band for Auto Memory Entry
Push the Control knob to [FM] or [AM].
2 Open Auto Memory Entry
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in
the memory Auto Memory Entry closes.
•
•
When the <AF (Alternative Frequency)> (page 22) is
ON, only RDS stations are put in the memory.
When Auto Memory Entry is done in the FM2 band,
the RDS stations preset in the FM1 band aren’t put in
the memory.
Likewise, when it is done in the FM3 band, RDS
stations preset in FM1 or FM2 aren’t put in the
memory.
Preset Tuning
Calling up the stations in the memory.
1 Select the band
Push the Control knob to [FM] or [AM].
2 Call up the station
Press the desired [1] — [6] button.
|
12
English
Function of the KDC-W4531/W4031/W409/3031A/3031G/309A/309G
RDS features
SCRL
+
VOL
AUD
SET UP
PTY
DISP
Q
MENU
OFF
SCAN
RDM
REP
ATT
DIM
-
TI
AME
TI
Control
knob
SRC
1 - 6
PTY indicator
TI indicator
Traffic Information
Switching to traffic information automatically
when a traffic bulletin starts even when you aren’t
listening to the radio.
•
Traffic information station can be switched when it
is on the Tuner Source or switched from the Tuner
Source during the reception of the Traffic bulletin.
Press the [TI] button.
Each time the button is pressed, the Traffic
information function turns ON and OFF.
When it’s ON, "TI" indicator is ON.
Radio Text Scroll
When a traffic information station isn’t being
received the "TI" indicator blinks.
When a traffic bulletin starts, "TRAFFIC" is
displayed it and it switches to traffic information.
Scrolling the displayed radio text.
Hold down on [FM] of the Control knob for at
least 1 second.
•
•
During reception of an AM station when the Traffic
Information function is turned ON, it switches to an
FM station.
During reception of traffic information the adjusted
volume is automatically remembered, and the next
time it switches to traffic information it’s automatically
the remembered volume.
Receiving other traffic information stations
Push the Control knob to [4] or [¢].
|
English
13
Function of the KDC-W4531/W4031/W409/3031A/3031G/309A/309G
RDS features
PTY (Program Type)
Selecting the Program Type and searching for a
•
Speech and Music include the Program type shown
station.
below.
Music: No.11 — 16, 25 — 29
Speech: No.2 — 10, 17 — 24, 30
The Program Type can be put in the [1] — [6] button
memory and called up quickly. Refer to the <Program
Type preset> (page 14).
The display language can be changed. Refer to
<Changing Language for PTY Function> (page 15).
1 Enter PTY mode
Press the Control knob.
•
•
During PTY mode the "PTY" indicator is ON.
•
This function can’t be used during a traffic bulletin or
AM reception.
3 Search for the selected Program Type
station
Push the Control knob to [4] or [¢].
When you want to search for other stations, push
[4] or [¢] of the Control knob again.
2 Select the Program Type
Push the Control knob to [FM] or [AM].
Each time the knob is pushed, the Program Type
switches as shown below.
No.
1.
Program Type
Speech
Display
"SPEECH"
"NEWS"
"AFFAIRS"
"INFO"
"SPORT"
•
When the selected Program Type isn’t found, "NO PTY"
is displayed. Select another Program Type.
2.
News
3.
4.
5.
Current Affairs
Information
Sport
4 Exit PTY mode
Press the Control knob.
6.
7.
8.
9.
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening Music
Light Classical
Serious Classical
Other Music
Weather
"EDUCATE"
"DRAMA"
"CULTURE"
"SCIENCE"
"VARIED"
"POP M"
"ROCK M"
"EASY M"
"LIGHT M"
"CLASSICS"
"OTHER M"
"WEATHER"
"FINANCE"
"CHILDREN"
"SOCIAL"
"RELIGION"
"PHONE IN"
"TRAVEL"
"LEISURE"
"JAZZ"
"COUNTRY"
"NATION M"
"OLDIES"
Program Type preset
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31
Putting the Program Type in the Preset button
memory and calling it up quickly.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 14).
2 Preset the Program Type
Press the desired [1] — [6] button for at least
2 seconds.
Finance
Children’s programs
Social Affairs
Religion
Phone In
Travel
Calling up the preset Program Type
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 14).
Leisure
2 Call up the Program Type
Press the desired [1] — [6] button.
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Music
"FOLK M"
"DOCUMENT"
"MUSIC"
|
14
English
Changing Language for PTY
Function
Selecting the Program Type display language.
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 14).
2 Enter Changing Language mode
Press the [TI] button.
3 Select the language
Push the Control knob to [FM] or [AM].
Each time the knob is pushed, the language
switches as shown below.
Language
English
French
Display
"ENGLISH"
"FRENCH"
"GERMAN"
German
4 Exit Changing Language mode
Press the [TI] button.
|
English
15
CD/Audio file/External disc control features
0
SCRL
+
VOL
AUD
SET UP
PTY
DISP
Q
MENU
OFF
SCAN
RDM
REP
F.SEL
M.RDM
ATT
DIM
-
TI
AME
SCAN RDM/ REP F.SEL M.RDM
3
Control
knob
SRC
Disc number
IN indicator
Track number
Track time
Function of the KDC-W4531
Playing CD & Audio file
Playing External Disc
When a disc is inserted
Press the [SRC] button.
Select the "CD" display.
Playing discs set in the optional accessory disc
player connected to this unit.
Press the [SRC] button.
Select the display for the disc player you want.
Display examples:
•
When a CD is inserted, the "IN" indicator is ON.
Pause and play
Display
"CD CH"
"MD CH"
Disc player
CD changer
MD changer
Press the control knob.
Each time the knob is pressed, it pauses and
plays.
Pause and play
Eject the CD
Press the Control knob.
Each time the knob is pressed, it pauses and
plays.
Press the [0] button.
•
Refer to <Playable Audio file> (page6) for the Audio
file by models which can be played.
•
•
Disc 10 is displayed as "0".
The functions that can be used and the information
that can be displayed will differ depending on the
external disc players being connected.
|
16
English
Fast Forwarding and Reversing
Scan Play
Playing the first part of each song on the disc you
are listening to and searching for the song you
want to listen to.
Fast Forwarding
Hold down on [¢] of the Control knob.
Release your finger to play the disc at that point.
1 Start Scan Play
Reversing
Press the [SCAN] button.
"TRAC SCN" (CD), "FILE SCN" (Audio file) is
displayed.
Hold down on [4] of the Control knob.
Release your finger to play the disc at that point.
2 Release it when the song you want to listen
to is played
•
The sound is not output while the Audio file is played.
Press the [SCAN] button.
Track/File Search
Searching for a song on the disc or in the Audio
file folder.
Random Play
Playing all the songs on the disc in random order.
Push the Control knob to [4] or [¢].
Press the [RDM] button.
Each time the button is pressed, Random Play
turns ON and OFF.
Function of disc changer/ Audio file
When it’s ON, "DISC RDM" (CD), "FOLD RDM"
(Audio file) is displayed.
Disc Search/Folder Search
Selecting the disc set in the Disc changer or the
folder recorded on the Audio file media.
•
When the Control knob is pushed to [¢], the next
song select starts.
Push the Control knob to [AM] or [FM].
Function of disc changer
Track/File/Disc/Folder Repeat
Magazine Random Play
Replaying the song, disc in the Disc changer or
Audio file folder you’re listening to.
Play the songs on all the discs in the disc changer
in random order.
Press the [REP] button.
Each time the button is pressed, the Repeat Play
switches as shown below.
Press the [M.RDM] button.
Each time the button is pressed, the Magazine
Random Play turns ON and OFF.
When it’s ON, "MGZN RDM" is displayed.
In CD & External disc source
Repeat play
Track Repeat
Disc Repeat (In Disc Changer)
OFF
Display
"TRAC REP"
"DISC REP"
"REP OFF"
•
When the Control knob is pushed to [¢], the next
song select starts.
In Audio file source
Repeat play
File Repeat
Folder Repeat
OFF
Display
"FILE REP"
"FOLD REP"
"REP OFF"
|
English
17
|