Installation
Instructions
41
64
0
Up
Down
On/Off
SuperFrost
Alarm
On/Off
Light
Zone
Up
Down
For wine cooler with
NoFrost freezer compartment and
Side-By-Side Units
with IceMaker
Instructions
de montage
Armoire de mise en température des
vins avec congélateur NoFrost et les
appareils côte à côte
2
-
-
6
4
8
avec IceMaker
6
-12
4
2
4
6
-
-
6
8
Instrucciones
de instalación
-12
3
2
4
6
-
-
6
8
Armario de acondicionamiento de
vinos con congelador NoFrost y
unidades lado a lado
-12
2
2
4
6
-
-
6
8
-12
con IceMaker
1
WF1051 / EWTNes 2956
7082 410-00 3405
IMPORTANT
TO THE INSTALLER
It is very important that the guidelines and
instructions are followed in the manual to ensure
proper installation and operation of the unit. The
Installation Guidelines section contains important
information for making sure the installation is
correct. Read and understand all the information in
Installation Guidelines, and in this manual before
the unit is installed.
A delight in freshness
WF1051 / EWTNes 2956
1
TABLE OF CONTENTS
Contents
Page
Installation Guidelines................................................................................. 3
Area Requirements............................................................................... 3
Electrical Requirement.......................................................................... 3
Customer’s Responsibility .................................................................... 3
Blocking For Safety............................................................................... 3
Unit Venting........................................................................................... 3
Planning Information................................................................................... 4
Cabinet Opening Dimensions............................................................... 4
Reversing Door Hinges............................................................................... 9
Door Opening Angle........................................................................... 12
Installation................................................................................................. 13
Blocking For Safety................................................................................... 16
IceMaker.................................................................................................... 17
Water Connection ............................................................................... 17
Connection to the Water Supply......................................................... 18
Side-By-Side Installation........................................................................... 20
A delight in freshness
WF1051 / EWTNes 2956
2
INSTALLATION GUIDELINES
Area Requirements
Verify the following:
WARNING
!
ELECTROCUTION HAZARD
• Floors can support refrigerator’s weight plus
approximately 1200 pounds (544 kg) of food
weight.
Electrical Grounding Required. This
appliance is equipped with a three-prong
(grounding) polarized plug for your
protection against possible shock hazards.
• Finished kitchen floor height has to be level.
Appliance must be shimmed to the floor level if
the floor heights are not equal to make sure air
vents are not obstructed.
DO NOT remove the round grounding
prong from the plug.
DO NOT use a two-prong grounding
adapter.
DO NOT use an extension cord to
connect power to the unit.
•
•
•
• Remove anything attached to rear or side walls
that can obstruct refrigerator opening.
• Cutout dimensions are accurate.
Customer’s Responsibility
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-
side installation) fused electrical supply is required.
We recommend using a dedicated circuit for this
appliance to prevent electrical overload. Follow
the National Electrical Code and local codes and
ordinances when installing the receptacle.
• Electrical outlet is in correct location.
Do not install this unit next to any other refrigerator
or freezer except another Liebherr model. Liebherr
models are designed to allow side-by-side
installation. They are equipped with a heating
element to eliminate condensation when units are
installed side by side. Installing this unit next to any
other refrigerator or freezer can cause condensation
or cause damage to the Liebherr unit.
Blocking For Safety
The anti-tip brackets must be installed to prevent
the unit from tipping after it is installed. Refer to
Blocking For Safety.
Electrical Requirement
Unit Venting
If codes require a separate grounding circuit to be
used, have a qualified electrician install the circuit.
DO NOT restrict the air flow. Air flow must be
provided for the unit to operate. The factory air
vents provide 31 square inches (200 cm²) of air
flow per unit. If you are replacing the factory air
vents with an overlay, the air flow must be the
same or greater than the factory air vents.
WARNING
!
Do not ground to a gas pipe. Check with a
qualified electrician if you are not sure the
appliance is properly grounded. Do not
have a fuse in the neutral or grounding
circuit.
WARNING
!
ELECTRICAL SHOCK HAZARD
• Electrically ground refrigerator.
• Do not use an extension cord.
• Failure to follow these instructions
could result in fire or electrical shock.
A delight in freshness
WF1051 / EWTNes 2956
3
PLANNING INFORMATION
Cabinet Opening Dimensions -
Figure 1
Allow units to open a minimum of 90° to prevent
problems removing drawers. With the door
opening 90°, you may have to move drawers
slightly to clear the door interior.
Refer to the minimum door clearances in the Pre-
Installation Specifications chart.
• Allow for a minimum 3-3/4" (95 mm) filler, for
corner installations, so the door can open to 90°.
If you’re using raised panels, consider using a
wider filler.
IMPORTANT
Refer to the full scale illustrations at the end
of this section for specifics on door openings
and filler size alternatives.
3"
"
(76mm)
"
"
Figure 1
A delight in freshness
WF1051 / EWTNes 2956
4
PLANNING INFORMATION
WF1051 - Figure 2
Figure 2
A delight in freshness
WF1051 / EWTNes 2956
5
PLANNING INFORMATION
Side-By-Side WF1051 and RB1400 - Figure 3
Figure 3
A delight in freshness
WF1051 / EWTNes 2956
6
PLANNING INFORMATION
The factory setting for the door to swing open
is 130°. Use this illustration to ensure other
cabinets or counters do not interfere with the
door opening.
130°
A delight in freshness
WF1051 / EWTNes 2956
7
PLANNING INFORMATION
The optional setting for the door to swing
open is 90°. Use this illustration to ensure
other cabinets or counters do not interfere
with the door opening.
90°
A delight in freshness
WF1051 / EWTNes 2956
8
REVERSING DOOR HINGES
The door hinges can be changed
from one side to the other if
required.
5
1. Figure 4: Top: Unscrew the
hinge pin (2) and remove the
screw (5).
2. Swivel out the door at the
top, ensuring that you do not
lose the stop (7) and bushing
(8); lift off the door and place
it on the floor. Unscrew the
handle from the upper door
2
5.
14
1.
X
Y
2. 8
2.
7
A
and pull out the cover caps (A). Then screw
the handle on the opposite side of the
upper door and place the plugs (Y) in the
open screw holes.
3.
9
W
3. Center: Pull out the hinge pin (9) with its
washer.
7
4.
4. Swivel out the lower door, lift it out and
place it on the floor. Take care not to lose
the stop (7) and washers (8). Unscrew the
handle from the lower door and pull out the
plugs (A). Then screw the handle on the
opposite side of the lower door and place
the plugs (Y) in the open screw holes.
5. Unscrew all the door fittings (14, 17) and
remove plugs (W, X).
8
W
Y
4.
A
17
5.
X
Figure 4
A delight in freshness
WF1051 / EWTNes 2956
9
REVERSING DOOR HINGES
6. Figure 5: Unscrew the lower hinge (13).
- Remove the washer, stops and bushing (14, 7, 8).
- Remove screw (Q).
8. Unscrew the center hinge (10) and cover (11),
pull them off to the side and after turning them
through 180°, slide them on again on the
opposite side and secure them.
- Transfer hinge pin (2) to the opposite side.
- Transfer screw (Q) to the opposite side.
- Turn the stop (7) through 180° and position
bushing (8) and washer as shown in the
detailed drawing. The flat side of the stop must
face forwards.
9. Place the lower door on the hinge pin (2) at the
bottom.
- Swivel in the door.
- Pay special attention to the bushing (12) in the
center hinge (10).
- Screw on hinge (13) on the new hinge side.
- Insert the hinge pin (9).
7. Install the door fittings as shown in Figure 5.
Insert the plugs (X) as shown in the detailed
drawing. Move plug (W) to the opposite side of
the lower door.
Figure 5
A delight in freshness
WF1051 / EWTNes 2956
10
REVERSING DOOR HINGES
10. Figure 6: Lift up cover (3) on handle side, push
12. Transfer hinge pin and screw to the respective
opposite side of the hinge (4), but do not insert
them in the hole or fasten them now.
outward; lift up cover (1) on hinge side and pull
off.
11. Unscrew mounting plate (21): first mounting
screw (20), then inner retaining screw (25).
- Unscrew hinge (4): first remove the mounting
screw (20), then retaining screws (25). Fit
hinge (4) to opposite side: for easy assembly,
fit hinge from above and first tighten with the
upper retaining screw (25) M5, then screw
(25) and finally mounting screw M4 (20).
- Turn mounting plate (21) through 180° and
screw tight again on the new handle side: first
retaining screw (25), then mounting screw
(20).
13. On the upper door, install the door fittings as
shown in Figure 6. Insert the plugs (X) as
shown in the detailed drawing. Move plug (W)
to the opposite side of the door.
14. Place the upper door on the center hinge, fit the
bushing (8), stop (7) and washer on the door,
swivel in the door at the top and insert and
secure the hinge pin (2) from above through the
hinge and stop. Insert screw (6) for fixing the
opening angle to 130°.
Check for proper alignment of all doors. Adjust
them if necessary using the slots on the hinge.
W
Figure 6
A delight in freshness
WF1051 / EWTNes 2956
11
REVERSING DOOR HINGES
Door Opening Angle - Figures 7, 8
The appliance is delivered with a door opening
angle of 130°.
If the angle is to be decreased to 90°, proceed as
follows:
• Insert attached screw (6) in the upper hinge as
shown in Figure 7.
• Insert eccentric (Z) in the lower hinge as shown
in Figure 8. Fix the eccentric with screw (V). The
eccentric pin must point away from the hinge
pin.
6
Figure 7
Q
V
Z
Figure 8
A delight in freshness
WF1051 / EWTNes 2956
12
INSTALLATION
Only install the winecooler/freezer in a stable
kitchen cabinet that has been properly aligned.
- Mount and fix the handles, depending on your
model and choice.
1.
2
1
Unpacking
Unpack the installation kit and check with the pro-
vided parts list if all parts are included.
3
2.
The part numbers given in the parts list are identical
to the numbers in the respective figures.
4
6
4
5
For installation you will need the following tools:
5
3.
6 4
5
Included:
8
- Star Key Torx® 15
- Star Key Torx® 20
- Star Key Torx® 25
- Socket Wrench 8 mm
- Open-end Wrench 10 mm
6
4
4.
6 4
5
Not in package:
- Phillips (star) screwdriver
- Level
6
4
- Ruler
Figure 16: Installation with Ventilation Grille Set:
1. Screw the installation frame at the top (1) onto
the appliance (2).
5.
2. Place the ventilation grille (3) on this, align
it in the center and secure at the front from
underneath.
7
6.
6.
3. Slide brackets (4) onto the side installation
7
frames (5) from above and below.
4. Using the frame (5), screw the brackets onto
the side wall*.
7
5. Slide the side installation frames (5) upwards
until they are in contact with the underside of
the ventilation grille.
7
6. Secure the side frames with the adhesive
section (7) to prevent them from sliding down.
Remove the protective film and affix the
adhesive sections over the upper brackets on
the handle and hinge sides.
Figure 16
A delight in freshness
13
WF1051 / EWTNes 2956
INSTALLATION
- Figure 17: Connect the appliance to the
main power supply.
- If the appliance is equipped with an
IceMaker, establish the connection for
the water supply. See “IceMaker, Water
Connection”.
1. Carefully slide the appliance into the cabinet
until the ventilation grille touches the surrounding
kitchen cabinet.
2. Align the appliance until it is parallel with the sur-
rounding kitchen cabinet. Use the open- end
wrench 10 mm (3) to adjust the feet at the front.
1.
2.
1
2
3
2
3
8 spanner
2
3
10 spanner
Figure 17
Turn clockwise for up and counterclock-wise
for down. For the rear use the adjusting
bolt (2). Turn clockwise for down and counter-
clockwise for up.
3.
Maximum adjustment: 19/64" (15 mm).
1
2
3. Figure 18: Align the appliance at the side
with the cabinet side panel and attach it with
screws (1).
- Cover the screws with cover caps (2).
4. Fit the ventilation grille at the bottom [(3) if
the door is hinged on the left, (4) if it is on the
right]: Secure the ventilation grille so that it
touches the floor and then adjust it using the
slots.
5
4.
3
5
4
5
5
Figure 18
A delight in freshness
WF1051 / EWTNes 2956
14
INSTALLATION
The following ventilation cross-section and
distances must be observed:
At least 31 square inches (200cm2)
- There must be a ventilation space of at
least 31 square inches (200 cm²) per
appliance in the cabinet plinth and under
the cabinet top panel.
- The depth of the ventilation duct at the
rear of the cabinet must be at least 1-
1/2" (38 mm).
1.
Alternatively:
1. For built-in appliances without
ventilation grilles and only with an
installation frame, ventilation must take
place through the ventilation duct at the
rear of the cabinet.
2
1
Built-in appliances with an installation frame:
•
Figure 19:
- Screw the complete installation frame (2)
to the appliance.
Figure 19
2. Built-in appliances with a wooden
ventilation grille:
Figure 20: Cut out the wooden trim for use
as a ventilation grille using the enclosed
template.
- The required ventilation cross-section
must be at least 31 square inches
(200 cm²) when a single appliance is
installed, which corresponds to template
“small” (If you install two appliances
side-byside, the cross-section must be at
least 62 square inches, (400 cm²), which
corresponds to template “double-size;”
for more information see “Side-by-Side
Installation”).
Remove the attachment bracket (2) from
the installation frame and screw it to the
appliance (1) from underneath. Place
the wooden ventilation grille (5) on the
appliance, align it in the center and secure
it from the rear using the attachment
bracket (2).
2
1/2"
•
5
(13 mm)
1
24"
(609.6 mm)
3-11/16"
(93,7 mm)
Figure 20
A delight in freshness
WF1051 / EWTNes 2956
15
BLOCKING FOR SAFETY
IMPORTANT
Figure 21: Secure the appliance in place so it does
The anti-tip brackets can be installed in either
direction or closer together. Always position
the anti-tip brackets as wide apart as possible,
but make sure they are anchored to two studs.
not tip forward when the fully stocked door is
opened.
1. Measure the distance from the floor to the
upper edge of the unit.
5. Using the adjustable roller base, raise the unit
until it makes contact with the brackets. Make
sure the front levelers are firmly on the floor to
prevent the appliance from tipping forward.
2. Locate and mark two wall studs (1) against the
wall where the appliance will be located. The
space between the unit top and the bottom
of the brackets must not be more than
1/4" (6.4 mm).
IMPORTANT
3. Make sure the screws (2) extend a minimum of
If your unit is positioned in between the
wall studs, a board can be secured to the
wall. Make sure the board is secured to the
studs with screws that will penetrate into the
studs a minimum of 1" (25.4 mm). The board
should be a minimum of 1" x 6" (25.4 mm x
152.4 mm) and long enough to secure both
ends to the wall studs.
1" (25.4 mm) into each of the wall studs.
4. Make sure the anti-tip brackets (3) extend
at least 3" (76.2 mm) over the unit and are
securely in place.
3
1
2
min 3"
Figure 21
A delight in freshness
WF1051 / EWTNes 2956
16
ICEMAKER
Water Connection - Figure 22
Please read the first three points of the safety
instructions and warnings before connecting the
appliance to the main water supply.
• The water pressure must be between 21.8-
87.0 psi (1.5-6 bar).
Use a 1/4" OD copper line to connect the water
supply to the solenoid valve. Allow extra length
to the water supply line to provide slack for easy
removal and to prevent the line from kinking.
This is not supplied with the appliance
(Figure 22).
• A shut-off valve, such as the saddle valve
illustration here, must be installed between the
hose line and the main water supply so the
water supply can be stopped if necessary.
Figure 22
• If you have hard water, we recommend you install
a water softener. Also, a filter must be installed if
the water contains solids such as sand.
Do not install the shut-off valve behind the
appliance.
• All equipment and devices used to supply the
water to the appliance must comply with the
current regulations for your geographical area.
A delight in freshness
17
WF1051 / EWTNes 2956
ICEMAKER
Connection to the Water Supply
- Figures 23, 24
1. Install the shut-off valve, water filter and
automatic shut-off device as required.
3. Open the shut-off valve for the water supply
and check the entire water system for leaks.
Before the appliance is used for the first time
a licensed plumber should bleed air from the
system.
Note
The solenoid valve is located at the rear of
your unit.
4. Insert the electrical plug for the combined
winecooler/freezer into the electrical outlet
(Figure 23).
2. Place a 1/4" OD copper tubing between the
shut-off valve and solenoid valve. Make sure
there is approximately 30" (70 cm) of excess
tubing behind the unit for easy connection.
5. Move the combined winecooler-freezer into
final position in the room.
IMPORTANT
The solenoid valve has a Metric R3/4 male
connection.
A R3/4(metric) to a 1/4" OD adapter and
cable clip are supplied with the icemaker.
Figure 24: Remove the cover cap (4) from
the solenoid valve (1). Install the connection
bracket (2) with sealing ring (6) on the
solenoid valve (1). Attach the copper tube to
the connection bracket (2). Secure the copper
tube (3) to the appliance using the cable
clip (5).
Figure 23
A delight in freshness
18
WF1051 / EWTNes 2956
ICEMAKER
1
4
1
6
2
3
5
5
Figure 24
A delight in freshness
WF1051 / EWTNes 2956
19
SIDE-BY-SIDE INSTALLATION
Figure 25: To install the WF1051 and RB1400
Unpacking
appliances side-by-side, proceed as follows:
- Always place the WF1051 and RB1400 with
the hinges on the left-hand side (looking from
the front).
Unpack the side by side installation kit and check
with the provided parts list if all parts are included.
The part numbers given in the parts list are identical
to the numbers in the respective figures.
Installation with SBS Ventilation Grille Set:
For installation you will need the following tools:
1. Affix the spacer (1) on the side wall of the
Included:
appliance – remove the protective film.
- Star Key Torx® 15
- Star Key Torx® 20
- Star Key Torx® 25
- Socket Wrench 8 mm
- Open-end Wrench 10 mm
2. Push the appliances together,
- align them parallel to each other.
3. Use a level on the top to align them to the same
height:
Not in package:
- Phillips (star) screwdriver
- Level
4. Use the open-end wrench 10 mm (3) to adjust
the feet at the front of the roller base. Turn
clockwise for up and counterclockwise for down.
For the rear, turn the adjusting bolt (2) clockwise
down and counterclockwise up.
- Ruler
4.
Figure 25
A delight in freshness
WF1051 / EWTNes 2956
20
SIDE-BY-SIDE INSTALLATION
5. Figure 26: Secure the installation frame (3) at
5.
2
3
the top to the appliances with screws (2).
- Align the appliance at the front bottom.
- Use the predrilled holes to align the installa-
tion frame (2).
- First mount the installation (3) frame with 4
screws (2) to one appliance, then align the
other appliance with the predrilled holes to
the installation frame (3) and secure it with
the screws (2).
6. Figure 26: Position the attachment brackets (6)
at the rear of the appliances at the top and
bottom. Slide the upper attachment bracket
upwards as far as possible. Secure it at the
side using the screws provided (5). Do not
overtighten!
6.
6
5
6.
5
6
c.a210
Figure 26
A delight in freshness
21
WF1051 / EWTNes 2956
SIDE-BY-SIDE INSTALLATION
7. Figure 27: Push the long carriage bolt M5x260 (7)
through the leveling wheels as shown. Fit in a
washer (8). Screw on the wing nut (9) and tighten it
manually. Do not overtighten.
8. Turn the adjustable roller base up. Otherwise you
will damage the floor when you push in the appli-
ances.
9. Secure the ventilation grille (10) to the appliance
with screws (11).
Push in the sealing strip (4) as shown.
10
9.
4
11
9
8
7
7.
7
8.
8 spanner
2
4
3
10 spanner
Figure 27
A delight in freshness
WF1051 / EWTNes 2956
22
SIDE-BY-SIDE INSTALLATION
10. Figure 28: Slide the side installation
10.
frames (15) upward until they are
in contact with the underside of the
ventilation grille, Figure 28.
11. Secure the side frames with the
adhesive section (17) to prevent
them from sliding down. Remove the
protective film and place the adhesive
sections over the upper brackets.
17
11.
12. Figure 29: Install anti-tip brackets for
each appliance. Refer to “Blocking For
Safety.”
17
15
15
11.
17
Figure 28
3
1
2
min 3"
Figure 29
A delight in freshness
WF1051 / EWTNes 2956
23
SIDE-BY-SIDE INSTALLATION
13. Figure 30, 31: Connect the appliances:
- to the main power supply and
- to the water supply if the appliance is
equipped with an IceMaker. See “IceMaker,
Water Connection,” Figure 30.
14. Carefully slide the connected appliances into
the recess until the ventilation grille touches the
top, Figure 31.
13.
15. Align the appliances by using only the outer
leveling wheels at the front (3) and rear (2).
Figure 30
14.
8 spanner
2
3
10 spanner
15.
Figure 31
A delight in freshness
WF1051 / EWTNes 2956
24
SIDE-BY-SIDE INSTALLATION
16. Figure 32: Attach the aligned combination to the
surrounding kitchen cabinet. Secure it through
the side frames using the screws (20) provided.
-
Cover the screws with cover caps (21).
17. Now adjust the center adjustable roller bases (22)
so that they make slight contact with the floor.
18. Install the lower ventilation grille (23): Secure the
ventilation grille so that it touches the floor and
adjust it using the slots. Do not overtighten!
20
21
16.
8 spanner
2
3
10 spanner
17.
22
18.
24
24
24
23
24
Figure 32
A delight in freshness
WF1051 / EWTNes 2956
25
SIDE-BY-SIDE INSTALLATION
1. For built-in appliances without ventilation
grilles and only with installation frame (2),
ventilation must take place through the
ventilation duct at the rear of the cabinet.
Ensure that the ventilation cross-section is at
least 31 square inches (200 cm²) per appliance.
At least 62 square inches (400 cm²) for side-
by-side installation of two appliances. Built-in
appliances with an installation frame:
- Figure 33: Screw the installation frame (2)
to the appliance through the attachment
brackets.
At least 31 square inches (200cm2)
per unit
”
/4
)
3
0
m
2
m
7
2
”
5
(
/4
)
3
0
m
2
m
7
2
5
(
1.
2
6
Figure 33
A delight in freshness
WF1051 / EWTNes 2956
26
SIDE-BY-SIDE INSTALLATION
Built-in appliances with a wooden ventilation
grille:
2. Figure 34: Cut out the wooden trim for use as a
ventilation grille using the attached template.
- The required ventilation cross-section must
be at least 62 square inches (400 cm²) for
side-by-side installation of two appliances,
which corresponds to the attached template
“double-size.”
- Remove the attachment brackets from the
installation frame (2) and screw them to the
appliance from underneath.
- Place the wooden ventilation grille (5) on the
appliance, align it in the center and secure it
from the rear using the attachment brackets.
2.
1/2"
(13 mm)
5
48"
(1219,2 mm)
3-11/16"
(93,7 mm)
Figure 34
A delight in freshness
WF1051 / EWTNes 2956
27
|
Pioneer Premier PRS D4000F User Manual
Pioneer AVX 7300 User Manual
Philips SHB6110 User Manual
Philips PHOTOFRAME SPF7208 User Manual
Philips BDP3390 User Manual
Onkyo Power Amplifier M 5000R User Manual
Nokia BH 202 User Manual
Lund Industries Headlight Flasher AT 500 User Manual
Kodak Playsport Video Camera 1191857 User Manual
KitchenAid 4KFP720ER2 User Manual