MODEL 622CM / MODEL 822CM
OWNER'S MANUAL
1 Mitek Plaza
Winslow, IL 61089
815-367-3000
800-225-5689
21A6502
OTHER PRODUCTS FROM MTX
In-Wall Loudspeakers
FEATURES
The MODEL 622CM and MODEL 822CM MTX In-Ceiling Speakers are designed
for use in small rooms or anywhere that both channels of a stereo signal need to
be reproduced while taking up a minimum amount of space.
MODEL 520W
MODEL 625W
5-1/4" Two-Way In-Wall Speaker
25mm Soft Dome Tweeter
Impedance: 8 ohms nominal
Sensitivity: 84dB
6-1/2" Two-Way In-Wall Speaker
25mm Soft Dome Tweeter
Impedance: 8 ohms nominal
Sensitivity: 85dB
Both models utilize a unique dual voice coil woofer design that allows both
channels of a stereo system to drive one cone. This feature coupled with a dual
tweeter system allow this unit to operate as two speakers in one.
50W RMS/100W Peak Music
Frequency Response: 53Hz-20kHz
11"H x 7 1/2"W x 2 1/2"D
55W RMS/110W Peak Music
Frequency Response: 55Hz-20kHz
12 1/16"H x 8 9/16"W x 2 7/8"D
This unit is of a water resistant design and therefore can be used in high humidity
areas such as a bathroom or laundry room.
MODEL 825W
8" Two-Way InWall Speaker
25mm Soft Dome Tweeter
Impedance: 8 ohms nominal
Sensitivity: 86dB
60W RMS/120W Peak Music
Frequency Response: 36Hz-20kHz
14 1/16"H x 10 1/16"W x 3 1/2"D
R+
R-
Home Loudspeakers
MONITOR6
MONITOR6C
6-1/2” Two-Way Home Loudspeaker
19mm Dome Tweeter
6-1/2” Center Channel Loudspeaker
19mm Dome Tweeter
Impedance: 8 ohms nominal
Sensitivity: 89dB
Impedance: 8 ohms nominal
Sensitivity: 92dB
100W RMS/200W Peak Music
Frequency Response: 55Hz-20kHz
12 3/4”H x 7 1/2”W x 8 1/2”D
100W RMS/150W Peak Music
Frequency Response: 60Hz-20kHz
7 1/2”H x 17 5/8”W x 8”D
MONITOR12
MONITOR10
L-
12” Three-Way Home Loudspeaker
19mm Dome Tweeter
10” Three-Way Home Loudspeaker
19mm Dome Tweeter
Impedance:8 ohms nominal
Sensitivity: 94dB
Impedance: 8 ohms nominal
Sensitivity: 92dB
L+
250W RMS/500W Peak Music
Frequency Response: 25Hz-20kHz
35”H x 13 1/8”W x 16 1/16”D
200W RMS/400W Peak Music
Frequency Response: 30Hz-20kHz
31 7/16”H x 11 1/8”W x 14 5/16”D
TECHNICAL ASSISTANCE
Otherwise, our technical service representatives can be reached by phone: 1-800-
CALL-MTX or by email: [email protected].
STEP 1
STEP 4
Using a stud finder (available at low cost at most hardware stores) or other accu-
rate method, locate center point between two joists and mark. Using template
provided, trace hole pattern on surface of ceiling
Attach loudspeaker wires to speaker terminals, observing correct polarity, and
position speaker frame up into cutout. Be careful not to pinch wires in the pro-
cess.
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol-
lowing traced pattern.
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings to
rotate out behind the mounting surface and secure the speaker in place.
STEP 3
STEP 6
Run loudspeaker wires to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of the
room or house. You can add a professional touch to your installation by using a
speaker terminal plate at the source location. Leave sufficient amount of wire at
speaker location (8 to 10 inches) to complete connection.
After the speaker panel is secured tightly, test for sound. When you are satisfied
the speaker is operational, affix grill. As grill is designed for a snug fit, you’ll need
to position one edge into slot first, and press or squeeze around perimeter of grill,
while pushing leading edges into grill slot.
|